Diagnostic guide
GoPro 'SD Error' or File Repair Icon – Recovering Your Footage Before You Format
Symptom
Your GoPro shows SD ERR, NO SD or a file repair icon, or the clips from a shoot will not play.
GoPro's own support page says SD ERR and NO SD mean the camera cannot properly communicate with the card. The file repair icon is a separate message: GoPro manuals describe it as appearing when a recording ended abruptly (battery, heat, card) and the video file was not properly saved. In both cases the footage is often on the card. A video that stopped mid-recording is typically missing its closing index, not its picture. The advice you will see first is to format the card. That wipes the footage you came for.
Do not
STOP - Do Not Format and Do Not Record On the Card
- Do not format the card in the camera, the GoPro app or on a computer
- Do not record anything new on the card
- Do not run a 'repair' tool that overwrites the original clip
- Do not keep power cycling the camera while the repair icon shows
- Do not delete the broken clips to 'make room'
Why this matters: GoPro's support guidance says formatting wipes the card and tells you to back up first. New recordings take over the storage where lost clips sit, and the SD Association explains that a quick format removes file entries but leaves data only until it is overwritten. A repair tool that works in place can also change the only copy of a damaged clip.
Cause
Most Likely Causes
- 01
Recording Cut Off Mid-Clip
High LikelihoodA battery that died, a camera that overheated, or a card pulled out while recording leaves an MP4 without the data that lets players open it.
- 02
Damaged File System on the Card
High LikelihoodThe same interruption can leave the card's directory unreadable, which produces SD ERR or a card the computer wants to format.
- 03
Card Not Suited to the Camera's Data Rate
Medium LikelihoodGoPro's support page notes a card that is not fast enough for the chosen resolution and frame rate can cause errors.
- 04
Worn or Failing Card
Less CommonCards used heavily in action cameras wear out. A card that fails tends to do so without warning.
What to do
Safe Diagnostic Checks
These checks are non-destructive and safe to perform. Follow them exactly as written.
Stop the camera, protect the card
- 01Switch the camera off and take the card out
- 02If the file repair icon was showing, let the camera finish only if it is repairing on its own; GoPro manuals describe newer models doing this automatically, older ones asking you to press a button
- 03If it stays on the icon or keeps restarting, take the card out and stop
- 04Do not insert the card in the camera again until the footage is copied
Copy the footage from a computer, read-only
- 01Use a microSD card reader or adapter on a computer
- 02If the DCIM folder opens, copy everything to the computer first, including clips that look tiny or broken
- 03Keep the original copies untouched and work only on duplicates
- 04If the computer says the disk must be formatted, choose Cancel
Small or zero-length clips are not always empty. Copy them anyway; a damaged clip can often still be rebuilt from its data.
Escalate
When Professional Recovery Is Required
You should seek professional data recovery if any of these apply:
- The computer does not show the card or asks to format it
- Clips copy but will not play, or play to a few seconds and stop
- The footage is a one-time event and not backed up
- The card was formatted or recorded over after the error
- A repair tool has already been run on the only copy
Process
Our Recovery Process
- Turnaround Time
- 2-5 business days
- Success Rate
- Assessed in the free evaluation; depends on the damage
What happens when you bring your drive to us:
- 01Free evaluation: read the card through a write-blocked path
- 02Create a full image of the card before any work
- 03Recover the clips; rebuild damaged videos from the camera's data stream where possible
- 04Check that recovered video plays through and the sound is in sync
- 05Return the footage on new media
FAQ
Frequently Asked Questions
Related
Related Guides
- 01
SD Card Corrupted After the Camera Battery Died – Getting the Photos Back
The camera battery died or the card was pulled mid-shoot, and now the camera reports a card error, 'cannot read card', or shows zero images. - 02
SD Card Says Cannot Be Accessed – Data Recovery
Your SD card shows 'cannot be accessed' or similar errors when you try to view your photos. - 03
Drone Crash – Recovering SD Card Footage and Flight Logs
Your drone crashed or lost power in flight and the footage is missing, the SD card shows an error, or the drone will not start. - 04
Canon 'Card Cannot Be Accessed' or Err 02 – Getting Your Photos Before You Format
Your Canon EOS says 'Card cannot be accessed. Reinsert/change card or format card in camera' or shows Err 02, and the only button it offers is Format.
Free diagnosis
Need Professional Data Recovery?
Free Diagnosis • No Recovery, No Charge
Our certified technicians have recovered thousands of drives with these exact symptoms. Get your free evaluation today.
- 97% Success Rate
- Across all device types
- ISO-5 Cleanroom
- Class 100 certified facility
- 24/7 Emergency
- Available for critical cases