Skip to content
Data recovery lab · Denver, Colorado24/7 emergency line (720) 222-0110Check Case
Back to Encryption, RAID & NAS Failures

Diagnostic guide

Synology 'Volume Crashed' or 'Degraded' Storage Pool – What To Do Before You Touch Anything

Updated Nov 15, 2026
7 min read

Symptom

DSM reports a storage pool as Degraded or a volume as Crashed, often after a drive failed, the wrong drive was pulled, or an update.

The two words mean different things. Per Synology's documentation, Degraded means the pool is running without full redundancy and can usually be repaired by replacing the failed drive, with repair starting from Storage Manager. Crashed is more serious: Synology says it cannot be repaired by the user and recommends contacting Synology Technical Support, and advises keeping the drives in the same order they were in when it crashed. In both cases the first rule is the same: do not pull drives or start rebuilds until you know what failed.

Do not

STOP - Do Not Rearrange or Rebuild

  • Do not pull and re-seat disks in random order
  • Do not start a Repair onto a replacement while another disk looks weak
  • Do not run mdadm --create or force-assemble commands over SSH
  • Do not delete the pool or volume and recreate it
  • Do not reset DSM or reinstall it to 'clear' the error

Why this matters: Synology notes that Repair does not guarantee data on a crashed volume will be recovered, and that disk order matters. A rebuild reads every remaining disk heavily; if a second disk is already weak, it can fail during the rebuild and take the array with it.

Cause

Most Likely Causes

  1. 01

    A Disk Dropped Out of the Pool

    High Likelihood

    One drive failed or disconnected. A single drive loss on a redundant pool shows as Degraded.

  2. 02

    The Wrong Drive Was Pulled

    Medium Likelihood

    A healthy drive was removed in place of the failed one, so two members were missing at once.

  3. 03

    Second Weak Disk

    Medium Likelihood

    Another disk with bad sectors fails during stress and the pool loses redundancy beyond what it can handle.

  4. 04

    Power Loss or Update Interruption

    Less Common

    An unclean shutdown or interrupted DSM update left the array in an inconsistent state.

What to do

Safe Diagnostic Checks

These checks are non-destructive and safe to perform. Follow them exactly as written.

CHECK-01

Read, don't act

  1. 01In Storage Manager, note the pool and volume status, and which disk bays are flagged
  2. 02Open HDD/SSD and read each drive's status and health info, without starting a test that stresses a weak disk
  3. 03Photograph the screen and the physical bay order, and label every drive with its bay number
  4. 04Export or screenshot the DSM log entries from the time it began

Information gathering only. Do not click Repair, Deactivate or Remove.

CHECK-02

Secure what is still readable

  1. 01If the shares still open (Degraded), copy the most important data to another drive or machine
  2. 02If a drive was pulled by mistake and you know which, do not do anything else before reading Synology's guidance for reinserting it
  3. 03If the volume is Crashed, power down in an orderly way and keep the drives in order

Escalate

When Professional Recovery Is Required

Critical - Act Immediately

You should seek professional data recovery if any of these apply:

  • The volume is Crashed
  • More than one disk is missing or flagged
  • A repair or rebuild has failed or stalled
  • The wrong drive was pulled and the order is uncertain
  • The NAS holds the only copy of business or family data

Process

Our Recovery Process

Turnaround Time
3-7 business days
Success Rate
Assessed in the free evaluation; depends on the damage

What happens when you bring your drive to us:

  1. 01Free evaluation: record disk order, RAID or SHR layout and the state of each member
  2. 02Image every member disk read-only; the NAS is not rebuilt
  3. 03Reconstruct the array virtually from the images
  4. 04Mount the volume (Btrfs or ext4) and check file system integrity on the copy
  5. 05Extract your data
  6. 06Return the data on new media

Ready to Recover Your Data?

Free diagnosis / No data, no charge guarantee

FAQ

Frequently Asked Questions

Related

Related Guides

Back to Encryption, RAID & NAS Failures

Free diagnosis

Need Professional Data Recovery?

Free Diagnosis • No Recovery, No Charge

Our certified technicians have recovered thousands of drives with these exact symptoms. Get your free evaluation today.

97% Success Rate
Across all device types
ISO-5 Cleanroom
Class 100 certified facility
24/7 Emergency
Available for critical cases