Skip to content
Data recovery lab · Denver, Colorado24/7 emergency line (720) 222-0110Check Case
Back to Windows & PC Drive Error Messages

Diagnostic guide

'Boot Device Not Found' and the Drive Is Missing in BIOS – Hardware or Setting?

Updated Nov 15, 2026
6 min read

Symptom

Your laptop or PC says 'Boot Device Not Found' or 'Reboot and select proper boot device', and the drive is not listed in BIOS.

Two very different things produce this screen. One is a setting: the storage mode (AHCI, RAID or Intel VMD) changed, so the computer can no longer reach a drive that is perfectly healthy. The other is hardware: the drive or its connection no longer answers. From the outside they look identical, which is why people reach for repair commands, reinstall Windows or swap drives, and those are the steps that turn a recoverable situation into a lost one.

Do not

STOP - Do Not Reinstall, Reset or Initialize

  • Do not reinstall Windows or run 'Reset this PC'
  • Do not run bootrec, CHKDSK or any repair command when the drive is not detected at all
  • Do not keep power cycling hoping it comes back
  • Do not fit a new drive and then initialize the old one in the same computer
  • Do not switch BIOS storage mode back and forth to see what happens

Why this matters: If the drive is not detected, repair commands have nothing to repair and a reinstall may overwrite what is there. If the cause is storage mode, flipping it can leave Windows unable to start even when the drive is healthy. Dell's documentation notes that on Intel 11th to 14th generation machines the drive sits behind Intel VMD and Windows installation media cannot see it without the Intel RST driver, which shows how easily a healthy drive can look absent.

Cause

Most Likely Causes

  1. 01

    Storage Mode Changed (AHCI / RAID / VMD)

    High Likelihood

    A BIOS update, a reset to defaults or a changed setting can alter how the computer talks to the drive. The drive is fine; the computer is asking the wrong way.

  2. 02

    Loose or Poorly Seated M.2 or SATA Connection

    Medium Likelihood

    A bumped laptop or a drive that was recently handled can lose contact. Reseating is a physical fix, but only worth doing carefully.

  3. 03

    The Drive Has Stopped Responding

    Medium Likelihood

    A failed controller, firmware lockup or mechanical fault means the drive is simply not answering. This is the case where nothing in settings will help.

  4. 04

    Boot Order or Boot Mode Issue

    Less Common

    The drive is detected but not set as the boot source. This one differs from the screen above because the drive then appears in BIOS.

What to do

Safe Diagnostic Checks

These checks are non-destructive and safe to perform. Follow them exactly as written.

CHECK-01

Find out whether BIOS can see the drive at all

  1. 01Enter BIOS or UEFI setup and look at the storage or boot section
  2. 02Write down or photograph what is listed: model name, size, and the current storage mode
  3. 03If the drive is listed, the problem is a boot setting, not a dead drive; stop and note it, do not change modes yet
  4. 04If it is not listed, continue to the connection check

Do not change the storage mode on a machine that already has Windows installed without writing down the original value first; switching it can stop Windows from starting.

CHECK-02

Check the simple physical things

  1. 01Unplug the charger, remove the battery if it is removable, and let the laptop sit for a few minutes
  2. 02If the drive is in an external enclosure or dock, try another cable and port directly on the computer
  3. 03Do not open a sealed laptop or force a drive out if you have not done it before
  4. 04If you cannot see the drive after this, stop

Escalate

When Professional Recovery Is Required

High Priority

You should seek professional data recovery if any of these apply:

  • The drive is not listed in BIOS even after checking connections
  • The drive is listed with a wrong name or size
  • The drive makes noise, gets very hot, or disappears and reappears
  • A repair, reset or reinstall has already been attempted
  • The data is not backed up

Process

Our Recovery Process

Turnaround Time
3-7 business days
Success Rate
Assessed in the free evaluation; depends on the damage

What happens when you bring your drive to us:

  1. 01Free evaluation: connect the drive outside the original computer and see whether it responds
  2. 02Separate a setting or connection problem from a drive that no longer answers
  3. 03If the drive responds, create an image through a read-only path
  4. 04If it does not, stabilise it at the controller or firmware level before imaging
  5. 05Rebuild the file system on the image and extract your files
  6. 06Verify that files open and return them on new media

Ready to Recover Your Data?

Free diagnosis / No data, no charge guarantee

FAQ

Frequently Asked Questions

Related

Related Guides

Back to Windows & PC Drive Error Messages

Free diagnosis

Need Professional Data Recovery?

Free Diagnosis • No Recovery, No Charge

Our certified technicians have recovered thousands of drives with these exact symptoms. Get your free evaluation today.

97% Success Rate
Across all device types
ISO-5 Cleanroom
Class 100 certified facility
24/7 Emergency
Available for critical cases