Diagnostic guide
Synology Shows 'Migratable' or 'Not Installed' After a DSM Update or a Move
Symptom
After a failed DSM update, a power cut or moving drives to another unit, find.synology.com or Synology Assistant shows your NAS as Migratable or Not Installed and asks you to install DSM.
Your data lives on the drives, in a volume that DSM manages. The operating system itself is stored on the drives too, so when it is missing or damaged the NAS asks to install it again. Synology's own migration instructions treat this as normal when drives move to a new compatible unit, with data kept if drives go in the same order. The danger is the installer: if it warns that all data on the drives will be deleted, Synology's instructions say to stop. The Install button looks routine and is the one step that is not.
Do not
STOP - Do Not Accept the 'All Data Will Be Deleted' Prompt
- Do not continue past a prompt that says all data on the drives will be deleted
- Do not reorder, swap or remove drives to 'try again'
- Do not install DSM from a file you are unsure about, or after the file reports as corrupted
- Do not start a RAID rebuild, repair or storage pool action to get the status to change
- Do not initialise or create a new storage pool
Why this matters: Synology's migration instructions say drives must go into the new unit in the same slot order as in the old one, and that an installer prompt that says all data will be deleted means you should stop and not continue. A wrong choice of install type or a changed drive order can turn a volume you could have opened into an empty one.
Cause
Most Likely Causes
- 01
DSM Installation Damaged by a Failed Update or Power Loss
High LikelihoodThe system partition on the drives is incomplete, so the NAS cannot start DSM. The data volume is separate and may be untouched.
- 02
Drives Moved to a Different Synology Unit
High LikelihoodA new unit sees disks that belong to another system. It shows Migratable when it recognises a compatible migration. Synology says migration only works between compatible models.
- 03
Drive Order Changed or a Drive Failing
Medium LikelihoodDrives in different slots, or one drive that no longer responds, change what the NAS thinks it is looking at.
- 04
Damaged Storage Pool or RAID Metadata
Less CommonThe installer may report that it cannot proceed because the array itself is damaged, which is a different and more serious situation.
What to do
Safe Diagnostic Checks
These checks are non-destructive and safe to perform. Follow them exactly as written.
Read the status without installing anything
- 01Power the NAS down and up once; check find.synology.com or Synology Assistant for the status shown
- 02Write down the exact words: Migratable, Not Installed, Configuration lost, or an error number
- 03Take a photo of every screen that mentions your drives or your data
- 04Do not click Install, Migrate or Reinstall at this stage
Record how the drives sit
- 01Power the NAS off cleanly and note which drive is in which bay before touching anything
- 02Label each drive with its bay number using tape on the tray, not the drive's label
- 03Check whether the unit that is now running is the original model or a compatible replacement
- 04Stop here; if the screen warns that data will be deleted, close it
Never pull drives while the NAS is mid-update. If the update is still running, wait or leave it off and ask for help.
Escalate
When Professional Recovery Is Required
You should seek professional data recovery if any of these apply:
- The installer says all data on the drives will be deleted
- A reinstall or migrate attempt has already been made
- DSM install fails repeatedly with a 'file corrupted' type error
- More than one drive is failing or one drive has already been replaced
- The NAS holds the only copy of business or family data
Process
Our Recovery Process
- Turnaround Time
- 2-5 business days
- Success Rate
- Assessed in the free evaluation; depends on the damage
What happens when you bring your drive to us:
- 01Free evaluation: record the bay order and read each drive's health outside the NAS
- 02Image every member drive through a read-only path
- 03Reassemble the array from the images and locate the volume
- 04Mount the volume read-only and extract shared folders
- 05Verify files open, return on new media
FAQ
Frequently Asked Questions
Related
Related Guides
- 01
Synology NAS Blinking Blue Light – Data Recovery
Your Synology NAS is stuck with a blinking blue status light and won't boot normally. - 02
Synology 'Volume Crashed' or 'Degraded' Storage Pool – What To Do Before You Touch Anything
DSM reports a storage pool as Degraded or a volume as Crashed, often after a drive failed, the wrong drive was pulled, or an update. - 03
RAID 5 Rebuild Failed with 2 Drives Offline
Your RAID 5 array has failed during rebuild or shows multiple drives offline. - 04
QNAP RAID Degraded or Storage Pool Lost – Do Not Rebuild Yet
Your QNAP reports a degraded RAID group, a read-only volume, or the storage pool has disappeared after a drive failed or a firmware update.
Background reading
Free diagnosis
Need Professional Data Recovery?
Free Diagnosis • No Recovery, No Charge
Our certified technicians have recovered thousands of drives with these exact symptoms. Get your free evaluation today.
- 97% Success Rate
- Across all device types
- ISO-5 Cleanroom
- Class 100 certified facility
- 24/7 Emergency
- Available for critical cases