Skip to content
Data recovery lab · Denver, Colorado24/7 emergency line (720) 222-0110Check Case
Back to SSD & Flash Storage Failures

Diagnostic guide

NVMe SSD Shows RAW or Unallocated After a Power Cut or Blue Screen

Updated Nov 15, 2026
6 min read

Symptom

After a power outage or a blue screen, your SSD is visible in BIOS but Windows calls it RAW, Unallocated or asks to initialize it.

The drive is usually still talking to the computer, and the files are usually still on it. What broke is the map that tells Windows where they are: the partition table or the file system's own records. An abrupt stop can leave exactly that map half-written. The danger is what comes next. Windows offers to initialize or format, guides tell you to run CHKDSK, and every one of those rewrites the very structures that would let the files be found.

Do not

STOP - Do Not Initialize, Format, Create a Volume or Run CHKDSK

  • Do not click Initialize Disk, and do not format when Windows offers
  • Do not right-click Unallocated space and create a New Simple Volume
  • Do not run diskpart clean, or CHKDSK /f or /r on a drive that may be failing
  • Do not keep rebooting to see whether it comes back
  • Do not install recovery software onto the same drive

Why this matters: Microsoft's own documentation says formatting erases all data, that initializing a disk already in use erases its data and that files should be saved first, and that you should not format a RAW partition or create a volume on Unallocated space if you are trying to recover files. An SSD also moves data around internally, so a rewrite of the structures can hide the files faster than on a hard drive.

Cause

Most Likely Causes

  1. 01

    Damaged Partition Table or File System Records

    High Likelihood

    The power cut interrupted a write to the structures that describe the volume. The files are still in the flash but Windows cannot find them.

  2. 02

    Controller Confused by the Sudden Power Loss

    Medium Likelihood

    The SSD's controller keeps its own map of where data lives. An abrupt stop can leave that map inconsistent, so the drive reports the wrong size or an empty disk.

  3. 03

    Failing Drive Whose Fault Showed Up With the Crash

    Medium Likelihood

    Sometimes the drive was already weak and the blue screen was a symptom, not the cause.

  4. 04

    Disk Marked Offline or a Port Issue

    Less Common

    Windows can mark a disk Offline after errors. Bringing it Online is harmless and sometimes all that is needed.

What to do

Safe Diagnostic Checks

These checks are non-destructive and safe to perform. Follow them exactly as written.

CHECK-01

Look, but change nothing

  1. 01Open Disk Management and note how the disk is listed: Online or Offline, RAW, Unallocated or Not Initialized, and its reported size
  2. 02If it says Offline, Microsoft's guidance is to right-click it and choose Online; this does not write to the drive's data
  3. 03Confirm the drive appears in BIOS with the right model name and size, and take a photo
  4. 04Check Device Manager for a warning on the storage controller
CHECK-02

Rule out the cable, slot and computer

  1. 01Shut down properly, then power on and check again
  2. 02If the SSD is in an enclosure, try another cable and a different USB port directly on the computer, not a hub
  3. 03Try the drive in a different computer or enclosure; Microsoft's guidance says a drive that fails on another PC points to the drive, not your PC
  4. 04Stop as soon as one attempt shows an error or a different size; do not try repeatedly

If Windows prompts to initialize or format at any step, choose Cancel.

Escalate

When Professional Recovery Is Required

High Priority

You should seek professional data recovery if any of these apply:

  • The disk stays RAW, Unallocated or Not Initialized after the checks above
  • The drive reports a wrong size or a strange model name in BIOS
  • It is the system drive and the computer will not boot
  • Someone already initialized, formatted or ran CHKDSK on it
  • The files are not backed up and you cannot recreate them

Process

Our Recovery Process

Turnaround Time
2-5 business days
Success Rate
Assessed in the free evaluation; depends on the damage

What happens when you bring your drive to us:

  1. 01Free evaluation: identify the controller family and confirm the drive responds
  2. 02Connect the drive through a read-only path so nothing is written to it
  3. 03Create an image of the readable flash
  4. 04Rebuild the partition and file system structures on the image, not the original
  5. 05Extract your folders and verify that files open
  6. 06Return the data on new media

Ready to Recover Your Data?

Free diagnosis / No data, no charge guarantee

FAQ

Frequently Asked Questions

Related

Related Guides

Back to SSD & Flash Storage Failures

Free diagnosis

Need Professional Data Recovery?

Free Diagnosis • No Recovery, No Charge

Our certified technicians have recovered thousands of drives with these exact symptoms. Get your free evaluation today.

97% Success Rate
Across all device types
ISO-5 Cleanroom
Class 100 certified facility
24/7 Emergency
Available for critical cases