Diagnostic guide
NVMe SSD Disappeared After a Firmware Update – Is the Data Still There?
Symptom
You updated your SSD's firmware and now the drive is missing from BIOS and Windows, or the update froze halfway.
A firmware update rewrites the small program that runs the drive's controller. If it is interrupted or the new version fails to start, the drive can stop answering the computer even though the memory chips still hold your files. That is why people describe it as bricked and why the data is often still there. What turns this into a worse problem is the response: repeated re-flashing, secure erase tools, or sending the drive back for a replacement. One caution on the other side: not every vanished drive is a failed update. Dell's documentation shows that a healthy drive behind Intel VMD can be invisible until the right driver is loaded, so check the simple explanations before you assume the worst.
Do not
STOP - Do Not Re-Flash, Secure Erase or Send It Back Yet
- Do not run the firmware update again, or a different version, on the dead drive
- Do not use Secure Erase, 'sanitize' or any reset tool from the vendor
- Do not return the drive for a warranty replacement before you have a copy of your files
- Do not keep power cycling it for hours hoping it reappears
- Do not initialise or format it if it does reappear as empty
Why this matters: A re-flash on a drive in an unknown state can change more of what the controller relies on, and an erase tool does exactly what its name says. A warranty swap sends your data away with the old drive. Microsoft also notes that initialising a disk in use erases its data.
Cause
Most Likely Causes
- 01
New Firmware Failed to Start the Controller
High LikelihoodThe update did not finish writing, or the new version does not run cleanly on that drive, so the controller stays in a locked or minimal state. The memory chips are usually unaffected.
- 02
Interrupted Update
Medium LikelihoodA power cut, crash or sleep during the flash leaves firmware half written.
- 03
Storage Mode or Driver Change on the Computer
Medium LikelihoodThe update tool or a BIOS change moved the drive behind Intel VMD or another mode. Dell's article shows that mode alone can hide a healthy drive from Windows Setup.
- 04
The Drive Was Already Failing
Less CommonThe update was the moment a weak drive finally stopped. Timing makes it look like cause and effect.
What to do
Safe Diagnostic Checks
These checks are non-destructive and safe to perform. Follow them exactly as written.
Check the computer side first
- 01Shut down fully, wait a minute, and start again once; do not repeat this loop
- 02Check BIOS: is the drive listed, with the right model name and size? Photograph what you see
- 03Check the storage mode (AHCI, RAID or VMD) and note it without changing it
- 04If you can, try the drive in another computer or a USB enclosure; Microsoft's guidance is that a drive that fails on another PC points to the drive, not your PC
If the drive is listed with a strange name or a tiny capacity, that is a controller in a minimal state. Stop; do not flash it again.
Record, then stop
- 01Write down the exact drive model, the firmware version you were updating to and the tool you used
- 02Keep the update tool's last on-screen message or log
- 03Check whether your data exists elsewhere: cloud sync, another computer, a backup
- 04Leave the drive switched off and untouched while you decide
Escalate
When Professional Recovery Is Required
You should seek professional data recovery if any of these apply:
- The drive is missing from BIOS or listed with a wrong name or capacity
- The update froze or the computer lost power during it
- The data is not backed up
- You are considering a warranty replacement
- A re-flash or erase has already been attempted
Process
Our Recovery Process
- Turnaround Time
- 3-7 business days
- Success Rate
- Assessed in the free evaluation; depends on the damage
What happens when you bring your drive to us:
- 01Free evaluation: identify the controller and its current state outside your computer
- 02Bring the controller back to a state where the memory can be read, without erasing
- 03Create a full image of the flash through a read-only path
- 04Rebuild the file system on the image, not on the drive
- 05Extract your files and verify they open
- 06Return the data on new media
FAQ
Frequently Asked Questions
Related
Related Guides
- 01
NVMe Drive Not Detected in BIOS After Crash
Your NVMe SSD is no longer detected in BIOS or the operating system after a crash or sudden event. - 02
Samsung SSD Suddenly Read-Only or Health Falling Fast – Copy Your Data Off First
Your Samsung SSD will not let you save or delete files, or Samsung Magician shows the health percentage dropping week by week. - 03
SSD Shows Up as 0 Bytes – Data Recovery
Your SSD appears in Windows but shows 0 bytes capacity or drastically wrong size. - 04
'Boot Device Not Found' and the Drive Is Missing in BIOS – Hardware or Setting?
Your laptop or PC says 'Boot Device Not Found' or 'Reboot and select proper boot device', and the drive is not listed in BIOS.
Background reading
Free diagnosis
Need Professional Data Recovery?
Free Diagnosis • No Recovery, No Charge
Our certified technicians have recovered thousands of drives with these exact symptoms. Get your free evaluation today.
- 97% Success Rate
- Across all device types
- ISO-5 Cleanroom
- Class 100 certified facility
- 24/7 Emergency
- Available for critical cases