Water itself is not the main enemy of a hard drive; what it leaves behind is. Minerals, dirt, and contaminants in the water corrode the circuit board and, if water got in through the drive's breather hole, can dry onto the platters as a film the heads crash on.
Don't power it on to test it, don't put it in rice, and don't use a hair dryer. Powering a wet board can short it, and spinning a drive with residue inside can destroy the heads and surfaces.
Many labs advise keeping a water-damaged drive from drying out on the way in: put it in a sealed plastic bag and bring it in quickly. Cleaning inside a drive is a cleanroom procedure.
Beginner · water damage · flood · corrosion · hard drive
Shut the laptop down right away, unplug the charger, and remove the battery if it's removable. Turn the laptop upside down in a tent shape so liquid drains away from the board. Don't turn it on to check whether it still works.
Sugary and acidic drinks keep corroding the board for days, even if the laptop seems fine at first. On many current laptops the storage is soldered to the logic board, so a corroded board can trap the data along with it.
If your files aren't backed up, say so when you take it in for repair. A shop that replaces a board without preserving data may hand back a working laptop with an empty drive; on soldered, encrypted models, repairing the original board is how the data is recovered.
Beginner · spill · laptop · liquid damage · corrosion
Flood water carries mud, sewage, and chemicals, so flooded equipment is both a data problem and a safety one. Wear gloves, and don't power anything on, including servers, NAS units, and desktops that look dry.
Remove drives only if you can do it without forcing anything, label each one with the device and slot it came from, and keep RAID members together. Bag drives individually; many labs suggest keeping them damp rather than letting residue dry inside.
Photograph everything before you move it, for insurance. Then prioritize: which systems hold data that exists nowhere else? Those go to the lab first.
Intermediate · flood · servers · insurance · contamination
Hard drive platters tolerate more heat than most people expect, so drives from burned computers are often worth evaluating even when the outside is scorched. The circuit board, heads, and plastic parts usually suffer first.
Smoke is a quieter threat. Soot is acidic and corrodes boards and connectors, and fine smoke particles can get inside a drive through its breather filter. Residue from dry-chemical fire extinguishers is corrosive too.
Don't try to clean or power a fire-damaged device. Keep it in a closed bag or box, handle it by the edges, and leave melted cases intact; prying them apart can crack platters or boards.
Intermediate · fire damage · smoke · soot · heat
A drive that was running when it fell is at the highest risk: the heads were flying a tiny distance above the spinning platters and can slap into the surface. A drive that was off, with its heads parked, is more robust, but a hard knock can still bend the head assembly, shift the platters, or jam the motor.
The first power-up after a drop is the riskiest moment. If the heads are bent, they can scrape the surface as soon as the platters spin.
If it clicks, beeps, or grinds afterward, unplug it and leave it off. Even if it seems to work, copy your important files off right away; drop damage sometimes shows up as a slow decline rather than an immediate failure.
Beginner · dropped drive · head crash · physical damage · portable drive
Desktop external drives and multi-bay enclosures need a separate power adapter, and these adapters look alike. Plugging in one with a higher voltage or reversed polarity can instantly burn the protection components and motor controller on the drive's board.
Check the label on the adapter against the label on the drive: voltage, polarity symbol, and connector should all match. Keep adapters with their devices.
If you suspect the wrong adapter was used, don't keep trying different ones. The damage is usually electrical and repairable, but each attempt with a shorted board puts the drive's motor and heads at risk.
Beginner · power adapter · voltage · external drive · pcb
Portable drives and flash drives often break at the connector: the port tears off the board, or the plug of a thumb drive snaps. Many portable hard drives have the USB port soldered directly onto the drive's own board, so there is no standard connector inside to fall back on.
Don't hold a broken connector in place to try to copy files. An intermittent connection can drop the drive mid-write and corrupt the file system, and flexing a cracked board can break more traces.
A lab can usually repair the connector or the board, or read the drive another way. On drives where the USB board also handles encryption, the original board has to be repaired rather than replaced.
Intermediate · usb connector · broken port · portable drive · flash drive
SD cards contain a controller and a memory chip, and microSD cards are usually monolithic: controller and memory sealed together in one tiny package. A card that is cracked or snapped may still hold intact data if the memory itself wasn't broken.
Don't tape it together and put it in a reader or camera. A cracked card can short, and forcing it into a slot can break it further or damage the device.
Recovery from a broken monolithic card means reading the memory through microscopic contact points on the package and rebuilding the data the controller would normally have handled. Keep every fragment.
Intermediate · microsd · broken card · monolithic · sd card
When a phone is crushed or bent, data recovery depends on the logic board, not the screen. The storage chip is soldered to the board, and on modern phones it is encrypted with keys held by the phone's own security hardware, so the chip can't simply be moved to another phone.
That makes recovery a board-level repair job: replacing damaged components and repairing cracked connections until the original phone boots far enough to unlock with your passcode. In some cases the processor and storage are moved together to a donor board.
Keep the phone off, don't charge a swollen or punctured battery, and bring every piece. You will need the passcode.
Intermediate · phone · crushed · bent · logic board
A swollen lithium battery is a fire risk. Stop charging and using the device, don't press on it, and keep it away from anything flammable. A swelling battery can also push against the logic board or screen and crack components.
The swelling itself usually doesn't harm stored data, but don't keep the device running to get files off it. A repair shop can remove the battery safely; tell them the data matters so they don't reset or replace the board without asking.
Damaged lithium batteries have special shipping rules, so ask before mailing a device that contains one.
Beginner · swollen battery · lithium · safety · laptop
Storage devices are built for a range of temperatures, and a car parked in the sun can exceed it. Heat can soften adhesives, warp plastic, and stress solder joints, and on hard drives it affects the lubricant and the heads' flying height. Flash memory loses its stored charge faster when hot, especially on worn cards and SSDs.
Let a hot device cool to room temperature before using it. If it then behaves strangely, makes noises, or has corrupted files, stop and copy what matters first.
As a habit, don't store backup drives, camera cards, or phones in vehicles, attics, or next to heaters.
Beginner · heat · hot car · overheating · flash retention
A drive or laptop that spent the night in a freezing car, or was shipped in winter, can collect condensation when brought into a warm room, just like a cold glass. Moisture forming on the board, or inside a hard drive, before it is powered on can cause shorts or head problems.
Leave it in its bag or box and let it reach room temperature for a few hours before turning it on. This matters most in dry climates where indoor heating creates a big temperature difference.
Cold alone rarely damages a powered-off drive. The risk is powering it while it is still cold and damp.
Beginner · cold · condensation · moisture · winter
Electrostatic discharge, the small shock you feel after walking across carpet, can damage the sensitive chips on drive boards, memory cards, and bare SSDs. Damage isn't always immediate; a part can be weakened and fail later.
When handling a bare drive or SSD, touch a grounded metal object first, hold it by the edges, avoid touching the gold contacts and board components, and store it in an anti-static bag.
If a drive stopped working right after being handled bare, mention it to the lab. Electrical damage on the board points the diagnosis in a different direction than a mechanical failure.
Beginner · static · esd · electronics · handling