Diagnostic guide
WD My Cloud EX2 Ultra Unreachable, Shares Gone or Volume Failure After a Firmware Update
Symptom
Your WD My Cloud EX2 Ultra disappeared from the network, the shares are missing, or the dashboard reports a volume failure after a firmware update.
Two very different faults share these symptoms. One is a connection or sharing problem: the NAS is running and the disks are fine, but you cannot reach it. The other is a real failure of a drive or of the volume. The EX2 Ultra holds two disks, and WD documents that it runs them as RAID 0, RAID 1 or JBOD/spanning. That matters a great deal: with RAID 1 one disk can fail and the data survives, with RAID 0 and JBOD it does not. The wrong 'fix' for the first fault can ruin the second.
Do not
STOP - Do Not Restore, Reformat or Change the RAID Mode
- Do not run a Quick or Full Restore or any factory restore
- Do not change the RAID mode: WD documents that it erases the data
- Do not swap or reorder the two drives in a RAID 0 or JBOD setup
- Do not create a new volume 'over' the old one
- Do not keep power cycling the NAS if a drive is clicking or missing
Why this matters: WD's own manual warns that changing the RAID configuration destroys the data on the drives, and WD's restore options reset or reformat to different degrees. A short reset that clears only the admin password is not the same as a restore that wipes the volume; mixing them up is how data is lost in the middle of a connection problem.
Cause
Most Likely Causes
- 01
Network or Sharing Problem After the Update
High LikelihoodThe NAS is healthy, but its address, login or sharing settings no longer match what your computer expects. Forum threads often describe credential or share-access problems after a firmware change.
- 02
A Drive Failed in a RAID 1
Medium LikelihoodThe NAS reports a degraded or failed volume. The data is intact on the surviving disk, but a careless replace or restore can ruin it.
- 03
A Drive Failed in RAID 0 or JBOD
Medium LikelihoodThere is no redundancy, so the data on the failed disk is not covered by the other. This needs hardware work on the failing disk.
- 04
Firmware Update Interrupted
Less CommonA power cut or crash during an update can leave the system incomplete, so the NAS does not come up. The data volume may be untouched.
What to do
Safe Diagnostic Checks
These checks are non-destructive and safe to perform. Follow them exactly as written.
Work out which kind of fault it is
- 01Check the NAS's front LEDs and record their colour and pattern
- 02Try reaching the dashboard by the NAS's IP address from your router's device list
- 03If the dashboard opens, note the RAID mode, each drive's health and the volume status; photograph them
- 04If a drive reports failed or is missing, stop here and do not replace anything yet
WD describes a 4-second reset that touches only the admin password and network mode, and separate restore procedures that go much further. Do not start any of them without knowing exactly which one it is.
Protect the data if it is readable
- 01If shares open, copy the most important folders to another device now
- 02Copy, do not move, and stop if the NAS slows to a crawl or a drive starts clicking
- 03Note which RAID mode is shown before doing anything else
- 04If shares are missing but the volume shows healthy, copy nothing and do not restore; leave it as it is
Escalate
When Professional Recovery Is Required
You should seek professional data recovery if any of these apply:
- The dashboard reports Volume Failure or a failed drive
- The NAS is set to RAID 0 or JBOD and a drive is failing
- The NAS will not boot after an interrupted firmware update
- A restore, RAID change or reset has already been tried
- The NAS holds the only copy of your files
Process
Our Recovery Process
- Turnaround Time
- 3-7 business days
- Success Rate
- Assessed in the free evaluation; depends on the damage
What happens when you bring your drive to us:
- 01Free evaluation: record the drives, their order and condition
- 02Image each drive separately through a read-only path, repairing a failing disk first
- 03Work out the RAID layout and reassemble the volume from the images
- 04Mount read-only and extract your shares
- 05Verify files open and return them on new media
FAQ
Frequently Asked Questions
Related
Related Guides
- 01
WD My Cloud Yellow Light Flashing – Data Recovery
Your WD My Cloud NAS has a solid or flashing yellow/amber front LED. - 02
RAID 5 Rebuild Failed with 2 Drives Offline
Your RAID 5 array has failed during rebuild or shows multiple drives offline. - 03
Synology 'Volume Crashed' or 'Degraded' Storage Pool – What To Do Before You Touch Anything
DSM reports a storage pool as Degraded or a volume as Crashed, often after a drive failed, the wrong drive was pulled, or an update. - 04
QNAP RAID Degraded or Storage Pool Lost – Do Not Rebuild Yet
Your QNAP reports a degraded RAID group, a read-only volume, or the storage pool has disappeared after a drive failed or a firmware update.
Background reading
Free diagnosis
Need Professional Data Recovery?
Free Diagnosis • No Recovery, No Charge
Our certified technicians have recovered thousands of drives with these exact symptoms. Get your free evaluation today.
- 97% Success Rate
- Across all device types
- ISO-5 Cleanroom
- Class 100 certified facility
- 24/7 Emergency
- Available for critical cases